VoIP Mailing List Archives
Mailing list archives for the VoIP community |
|
| View previous topic :: View next topic |
| Author |
Message |
admin at tootai.net
Guest
|
 Posted: Fri Mar 28, 2014 4:01 am Post subject: [asterisk-users] AMD with analog lines - DIALSTATUS empty |
 |
|
Hello,
I would like to use AMD on outgoing calls using analog line. I tested
with SPA3102 and cisco2811 as gw and asterisk 1.8.26.1 as well as 11.8.1
Other end is analog number behind another cisco/asterisk, also tested
calling a mobile number with the same result.
What I did: dial is done like exten => s,n,Dial(SIP/<IP gw>/<dialed
number>,,M(myMacro)), which tell Asterisk to execute myMacro when the
call is answered by calling party.
[myMacro]
exten => s,1,NoOP(Executed when call is answered)
same => n,AMD()
same => n,NoOp(Dial status=${DIALSTATUS})
same => n,NoOp(AMD status=${AMDSTATUS} cause=${AMDCAUSE})
same => n,MacroExit()
Problem is that [myMacro] is executed as soon as the call is going out
from the gw (cisco or linksys) and before called party answered.
DIALSTATUS is empty (should be ANSWER), AMDSTATUS=NOTSURE and
AMDCAUSE=TOOLONG-5000 which seems OK as DIALSTATUS isn't reliable.
The same dialplan using a SIP trunk is working as expected.
So question is, why, when using analog line, I dont get the right behavior.
Thanks for any hint
--
Daniel
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users |
|
| Back to top |
|
 |
rmudgett at digium.com
Guest
|
| Posted: Fri Mar 28, 2014 9:41 am Post subject: [asterisk-users] AMD with analog lines - DIALSTATUS empty |
|
|
On Fri, Mar 28, 2014 at 4:01 AM, Administrator TOOTAI <admin@tootai.net (admin@tootai.net)> wrote:
| Quote: | Hello,
I would like to use AMD on outgoing calls using analog line. I tested with SPA3102 and cisco2811 as gw and asterisk 1.8.26.1 as well as 11.8.1 Other end is analog number behind another cisco/asterisk, also tested calling a mobile number with the same result.
What I did: dial is done like exten => s,n,Dial(SIP/<IP gw>/<dialed number>,,M(myMacro)), which tell Asterisk to execute myMacro when the call is answered by calling party.
[myMacro]
exten => s,1,NoOP(Executed when call is answered)
same => n,AMD()
same => n,NoOp(Dial status=${DIALSTATUS})
same => n,NoOp(AMD status=${AMDSTATUS} cause=${AMDCAUSE})
same => n,MacroExit()
Problem is that [myMacro] is executed as soon as the call is going out from the gw (cisco or linksys) and before called party answered. DIALSTATUS is empty (should be ANSWER), AMDSTATUS=NOTSURE and AMDCAUSE=TOOLONG-5000 which seems OK as DIALSTATUS isn't reliable.
The same dialplan using a SIP trunk is working as expected.
So question is, why, when using analog line, I dont get the right behavior.
Thanks for any hint
|
Analog lines don't have a reliable way to know when the far end actually answers. Polarity
reversals could signal when the far end actually answers, but it isn't normally available or
standardized. Thus, the line is considered answered when dialing is complete.
Richard |
|
| Back to top |
|
|
admin at tootai.net
Guest
|
| Posted: Fri Mar 28, 2014 12:05 pm Post subject: [asterisk-users] AMD with analog lines - DIALSTATUS empty |
|
|
Le 28/03/2014 15:40, Richard Mudgett a écrit :
| Quote: |
On Fri, Mar 28, 2014 at 4:01 AM, Administrator TOOTAI
<admin@tootai.net <mailto:admin@tootai.net>> wrote:
Hello,
I would like to use AMD on outgoing calls using analog line. I
tested with SPA3102 and cisco2811 as gw and asterisk 1.8.26.1 as
well as 11.8.1 Other end is analog number behind another
cisco/asterisk, also tested calling a mobile number with the same
result.
What I did: dial is done like exten => s,n,Dial(SIP/<IP
gw>/<dialed number>,,M(myMacro)), which tell Asterisk to execute
myMacro when the call is answered by calling party.
[myMacro]
exten => s,1,NoOP(Executed when call is answered)
same => n,AMD()
same => n,NoOp(Dial status=${DIALSTATUS})
same => n,NoOp(AMD status=${AMDSTATUS} cause=${AMDCAUSE})
same => n,MacroExit()
Problem is that [myMacro] is executed as soon as the call is going
out from the gw (cisco or linksys) and before called party
answered. DIALSTATUS is empty (should be ANSWER),
AMDSTATUS=NOTSURE and AMDCAUSE=TOOLONG-5000 which seems OK as
DIALSTATUS isn't reliable.
The same dialplan using a SIP trunk is working as expected.
So question is, why, when using analog line, I dont get the right
behavior.
Thanks for any hint
Analog lines don't have a reliable way to know when the far end
actually answers. Polarity
reversals could signal when the far end actually answers, but it isn't
normally available or
standardized. Thus, the line is considered answered when dialing is
complete.
|
OK, so it's a no way.
Thanks for your answer
--
Daniel
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users |
|
| Back to top |
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Search
