VoIP Mailing List Archives

[John.Lee at compuware.com]

I have the following software installed in a Centos Box with a TE420 (5th Gen) card.
. Centos 6.5 64-bit
. Asterisk 1.4.22
. dahdi-linux-complete-2.9.1.1+2.9.1
. libpri-1.4.14.
Even without plugging in the ISDN into span 1, all 4 spans are flashing red.
Plugging an E1 into span 1 makes no difference.

My system.conf is just simply:
loadzone=au
defaultzone=au

span=1,1,0,ccs,hdb3,crc4
bchan=1-15
bchan=17-21
unused=22-31
dchan=16

span=2,0,0,esf,b8zs
fxols=32-55

Below is the dmesg.

dahdi: Version: 2.9.1.1
dahdi: Telephony Interface Registered on major 196
wct4xxp 0000:04:08.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
wct4xxp 0000:04:08.0: 5th gen card with initial latency of 2 and 1 ms per IRQ
wct4xxp 0000:04:08.0: Firmware Version: c01a016d
wct4xxp 0000:04:08.0: FALC Framer Version: 3.1
wct4xxp 0000:04:08.0: Not prepped yet!
wct4xxp 0000:04:08.0: Found a Wildcard: Wildcard TE420 (5th Gen)
wct4xxp 0000:04:08.0: firmware: requesting dahdi-fw-oct6114-128.bin
VPM450: echo cancellation for 128 channels
wct4xxp 0000:04:08.0: VPM450: hardware DTMF disabled.
wct4xxp 0000:04:08.0: VPM450: Present and operational servicing 4 span(s)
p4p1: no IPv6 routers present
dahdi_devices pci:0000:04:08.0: local span 1 is already assigned span 1
dahdi_devices pci:0000:04:08.0: local span 2 is already assigned span 2
dahdi_devices pci:0000:04:08.0: local span 3 is already assigned span 3
dahdi_devices pci:0000:04:08.0: local span 4 is already assigned span 4
wct4xxp 0000:04:08.0: TE4XXP: Span 1 configured for CCS/HDB3/CRC4
wct4xxp 0000:04:08.0: RCLK source set to span 1
wct4xxp 0000:04:08.0: Recovered timing mode, RCLK set to span 1
wct4xxp 0000:04:08.0: SPAN 1: Primary Sync Source
wct4xxp 0000:04:08.0: Span 2 configured for ESF/B8ZS
wct4xxp 0000:04:08.0: RCLK source set to span 1
wct4xxp 0000:04:08.0: Recovered timing mode, RCLK set to span 1
wct4xxp 0000:04:08.0: Span 3 configured for ESF/B8ZS
wct4xxp 0000:04:08.0: RCLK source set to span 1
wct4xxp 0000:04:08.0: Recovered timing mode, RCLK set to span 1
wct4xxp 0000:04:08.0: Span 4 configured for ESF/B8ZS
wct4xxp 0000:04:08.0: RCLK source set to span 1
wct4xxp 0000:04:08.0: Recovered timing mode, RCLK set to span 1
wct4xxp 0000:04:08.0: Setting yellow alarm span 1
wct4xxp 0000:04:08.0: RCLK source set to span 2
wct4xxp 0000:04:08.0: System timing mode, RCLK set to span 2
wct4xxp 0000:04:08.0: Setting yellow alarm span 2
wct4xxp 0000:04:08.0: RCLK source set to span 3
wct4xxp 0000:04:08.0: System timing mode, RCLK set to span 3
wct4xxp 0000:04:08.0: Setting yellow alarm span 3
wct4xxp 0000:04:08.0: RCLK source set to span 4
wct4xxp 0000:04:08.0: System timing mode, RCLK set to span 4
wct4xxp 0000:04:08.0: Setting yellow alarm span 4
wct4xxp 0000:04:08.0: All spans in alarm : No validspan to source RCLK from
wct4xxp 0000:04:08.0: RCLK source set to span 1

Any thoughts?

The contents of this e-mail are intended for the named addressee only. It contains information that may be confidential. Unless you are the named addressee or an authorized designee, you may not copy or use it, or disclose it to anyone else. If you received it in error please notify us immediately and then destroy it.

[rmeyerriecks at digium...]

On Fri, May 30, 2014 at 4:07 AM, Lee, John (Sydney)
<John.Lee@compuware.com> wrote: