VoIP Mailing List Archives
Mailing list archives for the VoIP community |
|
| View previous topic :: View next topic |
| Author |
Message |
lex at skoda.com.ua
Guest
|
 Posted: Wed Nov 12, 2014 11:20 am Post subject: [asterisk-users] E1 - Cisco - Asterisk and vice verso |
 |
|
Hi,
Change my Dynastar E1 gateway to Cisco with E1 module, but can't make
easiest dialplan. All my routing i made on asterisk, so i need that
cisco all calls from E1 send via sip to Asterisk and all calls came
from Asterisk by sip send to E1. From E1 to Asterisk already work, but
can't understand how send all from Asterisk SIP to E1 ?
Can you help ?
Thank you
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users |
|
| Back to top |
|
 |
rnewton at digium.com
Guest
|
| Posted: Fri Nov 14, 2014 5:48 pm Post subject: [asterisk-users] E1 - Cisco - Asterisk and vice verso |
|
|
On Wed, Nov 12, 2014 at 10:02 AM, Dmitriy Sirant <lex@skoda.com.ua> wrote:
| Quote: | Hi,
Change my Dynastar E1 gateway to Cisco with E1 module, but can't make
easiest dialplan. All my routing i made on asterisk, so i need that cisco
all calls from E1 send via sip to Asterisk and all calls came from Asterisk
by sip send to E1. From E1 to Asterisk already work, but can't understand
how send all from Asterisk SIP to E1 ?
Can you help ?
|
If you are taking SIP calls into Asterisk and want to send them out
E1, you need an Asterisk-compatible E1 board, such as:
http://www.digium.com/en/products/telephony-cards/digital/single-span
Your question isn't very specific, so if you are having problems with
dialplan you will need to elaborate on Asterisk version, hardware
drivers and Asterisk channel drivers in use, etc.
--
Rusty Newton
Digium, Inc. | Community Support Manager
445 Jan Davis Drive NW - Huntsville, AL 35806 - US
direct: +1 256 428 6200
Check us out at: http://digium.com & http://asterisk.org
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users |
|
| Back to top |
|
|
kevin.larsen at pionee...
Guest
|
| Posted: Fri Nov 14, 2014 5:57 pm Post subject: [asterisk-users] E1 - Cisco - Asterisk and vice verso |
|
|
| Quote: | | Quote: | Hi,
Change my Dynastar E1 gateway to Cisco with E1 module, but can't make
easiest dialplan. All my routing i made on asterisk, so i need that cisco
all calls from E1 send via sip to Asterisk and all calls came from Asterisk
by sip send to E1. From E1 to Asterisk already work, but can't understand
how send all from Asterisk SIP to E1 ?
Can you help ?
|
If you are taking SIP calls into Asterisk and want to send them out
E1, you need an Asterisk-compatible E1 board, such as:
|
I think, though I am not for sure, that he is asking how to route a call from Asterisk to the Cisco device that is acting as the gateway (i.e. the E1 is connected to the Cisco and will only be speaking SIP to Asterisk).
We had a similar setup before we replaced the Cisco with Digium Gateways. Basically we just set up a peer in asterisk with the IP address of the Cisco and routed external calls to it. The Cisco then actually placed the calls to the PSTN. Pretty painless, though sometimes a bit confusing to remember that if there were issues, you might have to check dialing rules in both Asterisk and in the Cisco. |
|
| Back to top |
|
|
bferrell at baywinds.org
Guest
|
| Posted: Fri Nov 14, 2014 7:15 pm Post subject: [asterisk-users] E1 - Cisco - Asterisk and vice verso |
|
|
On 11/14/2014 02:57 PM, Kevin Larsen wrote:
| Quote: | | Quote: | | Quote: | Hi,
Change my Dynastar E1 gateway to Cisco with E1 module, but can't make
easiest dialplan. All my routing i made on asterisk, so i need that cisco
all calls from E1 send via sip to Asterisk and all calls came from Asterisk
by sip send to E1. From E1 to Asterisk already work, but can't understand
how send all from Asterisk SIP to E1 ?
Can you help ?
|
If you are taking SIP calls into Asterisk and want to send them out
E1, you need an Asterisk-compatible E1 board, such as:
|
I think, though I am not for sure, that he is asking how to route a call from Asterisk to the Cisco device that is acting as the gateway (i.e. the E1 is connected to the Cisco
and will only be speaking SIP to Asterisk).
We had a similar setup before we replaced the Cisco with Digium Gateways. Basically we just set up a peer in asterisk with the IP address of the Cisco and routed external calls
to it. The Cisco then actually placed the calls to the PSTN. Pretty painless, though sometimes a bit confusing to remember that if there were issues, you might have to check
dialing rules in both Asterisk and in the Cisco.
|
Yep, I concur, that's what he's asking for. The syntax for Cisco dial-peers isn't a whole lot of fun, but not horrible either and once you know to call it a dial-peer, the
documentation is easy to google.
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users |
|
| Back to top |
|
|
lex at skoda.com.ua
Guest
|
| Posted: Sat Nov 15, 2014 1:49 pm Post subject: [asterisk-users] E1 - Cisco - Asterisk and vice verso |
|
|
On 2014-11-12 16:02:53 +0000, Dmitriy Sirant said:
| Quote: | Hi,
Change my Dynastar E1 gateway to Cisco with E1 module, but can't make
easiest dialplan. All my routing i made on asterisk, so i need that
cisco all calls from E1 send via sip to Asterisk and all calls came
from Asterisk by sip send to E1. From E1 to Asterisk already work, but
can't understand how send all from Asterisk SIP to E1 ?
Can you help ?
Thank you
|
Problem was in new ios version (c3825-adventerprisek9-mz.151-4.M7.bin)
where by default closed all incoming sip session, and i must enable it
by:
voice service voip
ip address trusted list
ipv4 192.168.132.248 255.255.255.255
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users |
|
| Back to top |
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Search
