VoIP Mailing List Archives
Mailing list archives for the VoIP community |
|
| View previous topic :: View next topic |
| Author |
Message |
eric at fnords.org
Guest
|
 Posted: Tue Mar 04, 2008 3:57 pm Post subject: [asterisk-users] Mitel SX-200 + * |
 |
|
I would strongly recommend ESF/B8ZS. If you have a RED alarm that means
the device does not see a line connected to it -- check cabling.
Mark Best wrote:
| Quote: | Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system
to work with *?
I'm not getting inbound or outbound calls to work. (Inbound caller gets
line busy tone.)
SETTINGS FROM MITEL:
I built a Crossover cable and connected it like this:
PSTN--T1--ASTRISK--T1--OLD MITEL
-Crossover Cable Pin-out:
1 - 4
2 - 5
4 - 1
5 - 2
Mitel Settings:
Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA)
(My config: span=1,1,0,d4,b8zs & e&m=1-24)
The card is a 24 channel T1 - not a PRI right? (T1 E&M Emulation Trunk:
1)
So does that mean I use E&M with Winkstart?
(signalling=em_w) (is this spelt right?)
(Wink setting is an assumption based upon a setting I saw in
the PBX called wink timer)
Using a Sangoma A104D:
zttool
-GAVE "OK" on PSTN
-Gave "RED" on MITEL
Timing
-Receiving Time from PSTN & Giving to the Mitel
What debugging can I do to get more information?
------------------------------------------------------------------------
_______________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
|
--
Consulting for Asterisk, Polycom, Sangoma, Digium, Cisco, LAN, WAN, QoS,
T-1, PRI, Frame Relay, Linux, and network design. Based near
Birmingham, AL. Now accepting clients worldwide. |
|
| Back to top |
|
 |
markbest at co.nezperc...
Guest
|
| Posted: Tue Mar 04, 2008 4:07 pm Post subject: [asterisk-users] Mitel SX-200 + * |
|
|
Eric,
Looks like my Mitel does support ESF; I'll try changing it. One question
before I do. If I change it right now, do you suppose my Telco
automatically adapt?
TELCO---T1---MITEL
-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Eric
Wieling
Sent: Tuesday, March 04, 2008 12:58 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Mitel SX-200 + *
I would strongly recommend ESF/B8ZS. If you have a RED alarm that means
the device does not see a line connected to it -- check cabling.
Mark Best wrote:
| Quote: | Does anyone have any experience getting a Mitel SX-200 EL/ML PBX
|
system
| Quote: | to work with *?
I'm not getting inbound or outbound calls to work. (Inbound caller
|
gets
| Quote: | line busy tone.)
SETTINGS FROM MITEL:
I built a Crossover cable and connected it like this:
PSTN--T1--ASTRISK--T1--OLD MITEL
-Crossover Cable Pin-out:
1 - 4
2 - 5
4 - 1
5 - 2
Mitel Settings:
Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA)
(My config: span=1,1,0,d4,b8zs & e&m=1-24)
The card is a 24 channel T1 - not a PRI right? (T1 E&M Emulation
|
Trunk:
| Quote: | 1)
So does that mean I use E&M with Winkstart?
(signalling=em_w) (is this spelt right?)
(Wink setting is an assumption based upon a setting I saw
|
in
| Quote: | the PBX called wink timer)
Using a Sangoma A104D:
zttool
-GAVE "OK" on PSTN
-Gave "RED" on MITEL
Timing
-Receiving Time from PSTN & Giving to the
|
Mitel
| Quote: |
What debugging can I do to get more information?
|
------------------------------------------------------------------------
--
Consulting for Asterisk, Polycom, Sangoma, Digium, Cisco, LAN, WAN, QoS,
T-1, PRI, Frame Relay, Linux, and network design. Based near
Birmingham, AL. Now accepting clients worldwide.
_______________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users |
|
| Back to top |
|
|
jsmith at digium.com
Guest
|
| Posted: Tue Mar 04, 2008 4:07 pm Post subject: [asterisk-users] Mitel SX-200 + * |
|
|
On Tue, 2008-03-04 at 12:34 -0800, Mark Best wrote:
| Quote: | Does anyone have any experience getting a Mitel SX-200 EL/ML PBX
system to work with *?
|
No, but I'll make a few comments anyway. I'm not sure if they'll help
you at all, but maybe it'll help explain a few things to someone else on
the list.
| Quote: | I?m not getting inbound or outbound calls to work. (Inbound caller
gets line busy tone.)
|
Is the T1 in alarm? You've first gotta get it out of alarm before you
can make calls on it. Alarms are usually caused by physical
connectivity problems, or problems with framing and/or linecoding.
| Quote: | Mitel Settings:
Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA)
|
Hmmmn... D4 and B8ZS together? That's bizarre. Usually people will use
D4 framing and AMI linecoding together, or ESF framing and B8ZS
linecoding. I've never seen anyone uuse B8ZS linecoding with D4
framing.
--
Jared Smith
Community Relations Manager
Digium, Inc. |
|
| Back to top |
|
|
jsmith at digium.com
Guest
|
| Posted: Tue Mar 04, 2008 4:16 pm Post subject: [asterisk-users] Mitel SX-200 + * |
|
|
On Tue, 2008-03-04 at 13:07 -0800, Mark Best wrote:
| Quote: | Looks like my Mitel does support ESF; I'll try changing it. One question
before I do. If I change it right now, do you suppose my Telco
automatically adapt?
|
I've never seen a telco automatically adapt to anything, especially
signaling changes on a T1.
--
Jared Smith
Community Relations Manager
Digium, Inc. |
|
| Back to top |
|
|
markbest at co.nezperc...
Guest
|
| Posted: Tue Mar 04, 2008 4:17 pm Post subject: [asterisk-users] Mitel SX-200 + * |
|
|
Jared,
Thanks for the help.
There are other T1 trunks (using AMI,D4) going to different departments;
however the trunk line talking to the Telco is what it is.
I do have the ability to change it to ESF, so I will try changing it -
do you suppose my Telco will automaticly adapt if I do? (I'm fairly
confident they support ESF.)
-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Jared
Smith
Sent: Tuesday, March 04, 2008 1:08 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Mitel SX-200 + *
On Tue, 2008-03-04 at 12:34 -0800, Mark Best wrote:
| Quote: | Does anyone have any experience getting a Mitel SX-200 EL/ML PBX
system to work with *?
|
No, but I'll make a few comments anyway. I'm not sure if they'll help
you at all, but maybe it'll help explain a few things to someone else on
the list.
| Quote: | I'm not getting inbound or outbound calls to work. (Inbound caller
gets line busy tone.)
|
Is the T1 in alarm? You've first gotta get it out of alarm before you
can make calls on it. Alarms are usually caused by physical
connectivity problems, or problems with framing and/or linecoding.
| Quote: | Mitel Settings:
Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA)
|
Hmmmn... D4 and B8ZS together? That's bizarre. Usually people will use
D4 framing and AMI linecoding together, or ESF framing and B8ZS
linecoding. I've never seen anyone uuse B8ZS linecoding with D4
framing.
--
Jared Smith
Community Relations Manager
Digium, Inc.
_______________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users |
|
| Back to top |
|
|
eric at fnords.org
Guest
|
| Posted: Tue Mar 04, 2008 4:37 pm Post subject: [asterisk-users] Mitel SX-200 + * |
|
|
The telco will never change the line coding or framing without a change
request being sent to your account rep.
Mark Best wrote:
| Quote: | Eric,
Looks like my Mitel does support ESF; I'll try changing it. One question
before I do. If I change it right now, do you suppose my Telco
automatically adapt?
TELCO---T1---MITEL
-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Eric
Wieling
Sent: Tuesday, March 04, 2008 12:58 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] Mitel SX-200 + *
I would strongly recommend ESF/B8ZS. If you have a RED alarm that means
the device does not see a line connected to it -- check cabling.
Mark Best wrote:
| Quote: | Does anyone have any experience getting a Mitel SX-200 EL/ML PBX
|
system
| Quote: | to work with *?
I'm not getting inbound or outbound calls to work. (Inbound caller
|
gets
| Quote: | line busy tone.)
SETTINGS FROM MITEL:
I built a Crossover cable and connected it like this:
PSTN--T1--ASTRISK--T1--OLD MITEL
-Crossover Cable Pin-out:
1 - 4
2 - 5
4 - 1
5 - 2
Mitel Settings:
Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA)
(My config: span=1,1,0,d4,b8zs & e&m=1-24)
The card is a 24 channel T1 - not a PRI right? (T1 E&M Emulation
|
Trunk:
| Quote: | 1)
So does that mean I use E&M with Winkstart?
(signalling=em_w) (is this spelt right?)
(Wink setting is an assumption based upon a setting I saw
|
in
| Quote: | the PBX called wink timer)
Using a Sangoma A104D:
zttool
-GAVE "OK" on PSTN
-Gave "RED" on MITEL
Timing
-Receiving Time from PSTN & Giving to the
|
Mitel
| Quote: |
What debugging can I do to get more information?
|
------------------------------------------------------------------------
|
--
Consulting for Asterisk, Polycom, Sangoma, Digium, Cisco, LAN, WAN, QoS,
T-1, PRI, Frame Relay, Linux, and network design. Based near
Birmingham, AL. Now accepting clients worldwide. |
|
| Back to top |
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Search
