VoIP Mailing List Archives
Mailing list archives for the VoIP community |
|
| View previous topic :: View next topic |
| Author |
Message |
ikka.tirta at gmail.com
Guest
|
 Posted: Tue Sep 13, 2016 8:51 am Post subject: [asterisk-users] Panasonic PBX connect to Asterisk |
 |
|
Hi,
Is there anyone here who has experience connecting Asterisk (ver 13. with PBX Panasonic KX-TDA600 ?
The architecture more less like this :Â
Telco Sip Trunk ---> Asterisk 13 ---> Panasonic KX-TDA600 ---> Phone / Fax
Thanks in advance,
Regards,
Ikka - Jakarta, Indonesia |
|
| Back to top |
|
 |
hmcgregor at biggeeks.org
Guest
|
| Posted: Wed Sep 14, 2016 12:40 am Post subject: [asterisk-users] Panasonic PBX connect to Asterisk |
|
|
Hi,
On 09/13/2016 06:51 AM, Ikka Tirtawidjaja wrote:
| Quote: | Hi,
Is there anyone here who has experience connecting Asterisk (ver 13. with PBX Panasonic KX-TDA600 ?
The architecture more less like this :
Telco Sip Trunk ---> Asterisk 13 ---> Panasonic KX-TDA600 ---> Phone / Fax
|
What connectivity do you currently use for the KX-TDA600? E1, T1, POTS, BRI?
Others have suggested a SIP to E1/T1 gateway, which would let you skip the asterisk box, if you don't have other uses for it.
Another option is to use a PCI-E E1/T1 interface card in the asterisk box, especially if you already have an E1 or T1 interface in the KX-TDA600. I personally don't like buying smaller then a dual T1/E1 card, as the price difference between a dual and a single is so small. If the KX-TDA600 is set-up for Analog/POTS, you can use a channel bank on the second T1/E1 port, and feed POTS into the KX-TDA600.
For a small installation that wanted to keep their Nortel Key System, and their Telco really wanted to provide a PRI instead of POTS (the Nortel could only take pots), we used a dual T1 PCI card in an asterisk box, ran PRI on the Telco interface, an ADIT 600 channel bank on the second interface, and handed 4 POTS lines to the Nortel Key System.
The key is to give your self the most flexibility to change later, and preserve your existing investment.
-Harry
| Quote: | Thanks in advance,
Regards,
Ikka - Jakarta, Indonesia
|
|
|
| Back to top |
|
|
ikka.tirta at gmail.com
Guest
|
| Posted: Wed Sep 14, 2016 12:52 am Post subject: [asterisk-users] Panasonic PBX connect to Asterisk |
|
|
Dear Harry,
Thx for the explanation.
My team manage building's PBX that use Asterisk 13.x.Â
We use Asterisk PBX for this buildings that have apartment and office customer.
From my Asterisk PBX, we connect to IPPhone (yealink) or ATA Converter (cisco SPA112).Â
Others are using PBX like panasonic analog, audiocodes SBC, etc, and we use ATA Converter to convert from SIP to Analog (CO Line)
Now, we have a new customer (tenant) that have Panasonic TDA600.Â
If we use FXS or ATA Converter, its going to have a lot of that, because this tenant going to use about 60 ext / sip line.
Replacing asterisk PBX on my (company) side or replace TDA600 on my customer side is not acceptable.Â
So we need to find a "win-win" solution for this.
Thx in advance,
Ikka
On Wed, Sep 14, 2016 at 12:40 PM, Harry McGregor <hmcgregor@biggeeks.org (hmcgregor@biggeeks.org)> wrote:
| Quote: |
Hi,
On 09/13/2016 06:51 AM, Ikka Tirtawidjaja wrote:
| Quote: | Hi,
Is there anyone here who has experience connecting Asterisk (ver 13. with PBX Panasonic KX-TDA600 ?
The architecture more less like this :Â
Telco Sip Trunk ---> Asterisk 13 ---> Panasonic KX-TDA600 ---> Phone / Fax
|
What connectivity do you currently use for the KX-TDA600? E1, T1, POTS, BRI?
Others have suggested a SIP to E1/T1 gateway, which would let you skip the asterisk box, if you don't have other uses for it.
Another option is to use a PCI-E E1/T1 interface card in the asterisk box, especially if you already have an E1 or T1 interface in the KX-TDA600. I personally don't like buying smaller then a dual T1/E1 card, as the price difference between a dual and a single is so small. If the KX-TDA600 is set-up for Analog/POTS, you can use a channel bank on the second T1/E1 port, and feed POTS into the KX-TDA600.
For a small installation that wanted to keep their Nortel Key System, and their Telco really wanted to provide a PRI instead of POTS (the Nortel could only take pots), we used a dual T1 PCI card in an asterisk box, ran PRI on the Telco interface, an ADIT 600 channel bank on the second interface, and handed 4 POTS lines to the Nortel Key System.
The key is to give your self the most flexibility to change later, and preserve your existing investment.
-Harry
| Quote: | Thanks in advance,
Regards,
Ikka - Jakarta, Indonesia
|
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
Join the Asterisk Community at the 13th AstriCon, September 27-29, 2016
   http://www.asterisk.org/community/astricon-user-conference
New to Asterisk? Start here:
   https://wiki.asterisk.org/wiki/display/AST/Getting+Started
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users
|
|
|
| Back to top |
|
|
hmcgregor at biggeeks.org
Guest
|
| Posted: Wed Sep 14, 2016 1:05 am Post subject: [asterisk-users] Panasonic PBX connect to Asterisk |
|
|
Hi,
You need to find out more about the configuration of this specific TDA600, as it could be either POTS or E1, once you know that, you can determine what options are best.
-Harry
On 09/13/2016 10:51 PM, Ikka Tirtawidjaja wrote:
| Quote: | Dear Harry,
Thx for the explanation.
My team manage building's PBX that use Asterisk 13.x.
We use Asterisk PBX for this buildings that have apartment and office customer.
From my Asterisk PBX, we connect to IPPhone (yealink) or ATA Converter (cisco SPA112).
Others are using PBX like panasonic analog, audiocodes SBC, etc, and we use ATA Converter to convert from SIP to Analog (CO Line)
Now, we have a new customer (tenant) that have Panasonic TDA600.
If we use FXS or ATA Converter, its going to have a lot of that, because this tenant going to use about 60 ext / sip line.
Replacing asterisk PBX on my (company) side or replace TDA600 on my customer side is not acceptable.
So we need to find a "win-win" solution for this.
Thx in advance,
Ikka
On Wed, Sep 14, 2016 at 12:40 PM, Harry McGregor <hmcgregor@biggeeks.org (hmcgregor@biggeeks.org)> wrote:
| Quote: |
Hi,
On 09/13/2016 06:51 AM, Ikka Tirtawidjaja wrote:
| Quote: | Hi,
Is there anyone here who has experience connecting Asterisk (ver 13. with PBX Panasonic KX-TDA600 ?
The architecture more less like this :
Telco Sip Trunk ---> Asterisk 13 ---> Panasonic KX-TDA600 ---> Phone / Fax
|
What connectivity do you currently use for the KX-TDA600? E1, T1, POTS, BRI?
Others have suggested a SIP to E1/T1 gateway, which would let you skip the asterisk box, if you don't have other uses for it.
Another option is to use a PCI-E E1/T1 interface card in the asterisk box, especially if you already have an E1 or T1 interface in the KX-TDA600. I personally don't like buying smaller then a dual T1/E1 card, as the price difference between a dual and a single is so small. If the KX-TDA600 is set-up for Analog/POTS, you can use a channel bank on the second T1/E1 port, and feed POTS into the KX-TDA600.
For a small installation that wanted to keep their Nortel Key System, and their Telco really wanted to provide a PRI instead of POTS (the Nortel could only take pots), we used a dual T1 PCI card in an asterisk box, ran PRI on the Telco interface, an ADIT 600 channel bank on the second interface, and handed 4 POTS lines to the Nortel Key System.
The key is to give your self the most flexibility to change later, and preserve your existing investment.
-Harry
| Quote: | Thanks in advance,
Regards,
Ikka - Jakarta, Indonesia
|
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
Join the Asterisk Community at the 13th AstriCon, September 27-29, 2016
http://www.asterisk.org/community/astricon-user-conference
New to Asterisk? Start here:
https://wiki.asterisk.org/wiki/display/AST/Getting+Started
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
|
|
|
|
| Back to top |
|
|
shmaltz at gmail.com
Guest
|
| Posted: Thu Sep 15, 2016 3:29 pm Post subject: [asterisk-users] Panasonic PBX connect to Asterisk |
|
|
Use a sip to PRI gateway or a PRI card in the asterisk system. Connect that to the Panasonic TDA600 using a PRI card on the panasonic side (KX-TDA0290).this will be the most worry free solution.
On Wed, Sep 14, 2016 at 2:05 AM, Harry McGregor <hmcgregor@biggeeks.org (hmcgregor@biggeeks.org)> wrote:
| Quote: |
Hi,
You need to find out more about the configuration of this specific TDA600, as it could be either POTS or E1, once you know that, you can determine what options are best.
-Harry
On 09/13/2016 10:51 PM, Ikka Tirtawidjaja wrote:
| Quote: | Dear Harry,
Thx for the explanation.
My team manage building's PBX that use Asterisk 13.x.Â
We use Asterisk PBX for this buildings that have apartment and office customer.
From my Asterisk PBX, we connect to IPPhone (yealink) or ATA Converter (cisco SPA112).Â
Others are using PBX like panasonic analog, audiocodes SBC, etc, and we use ATA Converter to convert from SIP to Analog (CO Line)
Now, we have a new customer (tenant) that have Panasonic TDA600.Â
If we use FXS or ATA Converter, its going to have a lot of that, because this tenant going to use about 60 ext / sip line.
Replacing asterisk PBX on my (company) side or replace TDA600 on my customer side is not acceptable.Â
So we need to find a "win-win" solution for this.
Thx in advance,
Ikka
On Wed, Sep 14, 2016 at 12:40 PM, Harry McGregor <hmcgregor@biggeeks.org (hmcgregor@biggeeks.org)> wrote:
| Quote: |
Hi,
On 09/13/2016 06:51 AM, Ikka Tirtawidjaja wrote:
| Quote: | Hi,
Is there anyone here who has experience connecting Asterisk (ver 13. with PBX Panasonic KX-TDA600 ?
The architecture more less like this :Â
Telco Sip Trunk ---> Asterisk 13 ---> Panasonic KX-TDA600 ---> Phone / Fax
|
What connectivity do you currently use for the KX-TDA600? E1, T1, POTS, BRI?
Others have suggested a SIP to E1/T1 gateway, which would let you skip the asterisk box, if you don't have other uses for it.
Another option is to use a PCI-E E1/T1 interface card in the asterisk box, especially if you already have an E1 or T1 interface in the KX-TDA600. I personally don't like buying smaller then a dual T1/E1 card, as the price difference between a dual and a single is so small. If the KX-TDA600 is set-up for Analog/POTS, you can use a channel bank on the second T1/E1 port, and feed POTS into the KX-TDA600.
For a small installation that wanted to keep their Nortel Key System, and their Telco really wanted to provide a PRI instead of POTS (the Nortel could only take pots), we used a dual T1 PCI card in an asterisk box, ran PRI on the Telco interface, an ADIT 600 channel bank on the second interface, and handed 4 POTS lines to the Nortel Key System.
The key is to give your self the most flexibility to change later, and preserve your existing investment.
-Harry
| Quote: | Thanks in advance,
Regards,
Ikka - Jakarta, Indonesia
|
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
Join the Asterisk Community at the 13th AstriCon, September 27-29, 2016
   http://www.asterisk.org/community/astricon-user-conference
New to Asterisk? Start here:
   https://wiki.asterisk.org/wiki/display/AST/Getting+Started
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users
|
|
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
Join the Asterisk Community at the 13th AstriCon, September 27-29, 2016
   http://www.asterisk.org/community/astricon-user-conference
New to Asterisk? Start here:
   https://wiki.asterisk.org/wiki/display/AST/Getting+Started
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users
|
|
|
| Back to top |
|
|
ikka.tirta at gmail.com
Guest
|
| Posted: Fri Sep 16, 2016 4:45 am Post subject: [asterisk-users] Panasonic PBX connect to Asterisk |
|
|
Dear all,
thanks for the help.
I'm going to try using E1 gateway to convert sip to e1.
-ikka-
On Fri, Sep 16, 2016 at 3:28 AM, C F <shmaltz@gmail.com (shmaltz@gmail.com)> wrote:
| Quote: | Use a sip to PRI gateway or a PRI card in the asterisk system. Connect that to the Panasonic TDA600 using a PRI card on the panasonic side (KX-TDA0290).this will be the most worry free solution.
On Wed, Sep 14, 2016 at 2:05 AM, Harry McGregor <hmcgregor@biggeeks.org (hmcgregor@biggeeks.org)> wrote:
| Quote: |
Hi,
You need to find out more about the configuration of this specific TDA600, as it could be either POTS or E1, once you know that, you can determine what options are best.
-Harry
On 09/13/2016 10:51 PM, Ikka Tirtawidjaja wrote:
| Quote: | Dear Harry,
Thx for the explanation.
My team manage building's PBX that use Asterisk 13.x.Â
We use Asterisk PBX for this buildings that have apartment and office customer.
From my Asterisk PBX, we connect to IPPhone (yealink) or ATA Converter (cisco SPA112).Â
Others are using PBX like panasonic analog, audiocodes SBC, etc, and we use ATA Converter to convert from SIP to Analog (CO Line)
Now, we have a new customer (tenant) that have Panasonic TDA600.Â
If we use FXS or ATA Converter, its going to have a lot of that, because this tenant going to use about 60 ext / sip line.
Replacing asterisk PBX on my (company) side or replace TDA600 on my customer side is not acceptable.Â
So we need to find a "win-win" solution for this.
Thx in advance,
Ikka
On Wed, Sep 14, 2016 at 12:40 PM, Harry McGregor <hmcgregor@biggeeks.org (hmcgregor@biggeeks.org)> wrote:
| Quote: |
Hi,
On 09/13/2016 06:51 AM, Ikka Tirtawidjaja wrote:
| Quote: | Hi,
Is there anyone here who has experience connecting Asterisk (ver 13. with PBX Panasonic KX-TDA600 ?
The architecture more less like this :Â
Telco Sip Trunk ---> Asterisk 13 ---> Panasonic KX-TDA600 ---> Phone / Fax
|
What connectivity do you currently use for the KX-TDA600? E1, T1, POTS, BRI?
Others have suggested a SIP to E1/T1 gateway, which would let you skip the asterisk box, if you don't have other uses for it.
Another option is to use a PCI-E E1/T1 interface card in the asterisk box, especially if you already have an E1 or T1 interface in the KX-TDA600. I personally don't like buying smaller then a dual T1/E1 card, as the price difference between a dual and a single is so small. If the KX-TDA600 is set-up for Analog/POTS, you can use a channel bank on the second T1/E1 port, and feed POTS into the KX-TDA600.
For a small installation that wanted to keep their Nortel Key System, and their Telco really wanted to provide a PRI instead of POTS (the Nortel could only take pots), we used a dual T1 PCI card in an asterisk box, ran PRI on the Telco interface, an ADIT 600 channel bank on the second interface, and handed 4 POTS lines to the Nortel Key System.
The key is to give your self the most flexibility to change later, and preserve your existing investment.
-Harry
| Quote: | Thanks in advance,
Regards,
Ikka - Jakarta, Indonesia
|
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
Join the Asterisk Community at the 13th AstriCon, September 27-29, 2016
   http://www.asterisk.org/community/astricon-user-conference
New to Asterisk? Start here:
   https://wiki.asterisk.org/wiki/display/AST/Getting+Started
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users
|
|
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
Join the Asterisk Community at the 13th AstriCon, September 27-29, 2016
   http://www.asterisk.org/community/astricon-user-conference
New to Asterisk? Start here:
   https://wiki.asterisk.org/wiki/display/AST/Getting+Started
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users
|
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
Join the Asterisk Community at the 13th AstriCon, September 27-29, 2016
   http://www.asterisk.org/community/astricon-user-conference
New to Asterisk? Start here:
   https://wiki.asterisk.org/wiki/display/AST/Getting+Started
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users
|
|
|
| Back to top |
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Search
