VoIP Mailing List Archives

[niall.crosby at gmail.com]

Hi,

This might be Sangoma config issue, so apologies in advance for
posting it here if it is. I am waiting for Sangoma helpdesk to get
back to me!

But I have a Sangoma a101 and trying to get it working with
Freeswitch. Have E1 line coming from telco and everything set up
correctly (to my best efforts), however when Freeswitch starts, it
says:

2009-07-30 15:17:15.446569 [ERR] mod_openzap.c:1953 Error starting
OpenZAP span 1 mode: user dialect: euro error:

Also I'm getting the following Sangoma alarms:

***** w1g1: E1 Alarms (Framer) *****

ALOS: OFF | LOS: ON
RED: ON | AIS: OFF
OOF: ON | RAI: OFF

***** w1g1: E1 Alarms (LIU) *****

Short Circuit: ON
Open Circuit: OFF
Loss of Signal: ON


Can someone tell me where I should be focusing my attention - on the
Sangoma config or the Freeswitch config?

Also what state should the Sangoma alarms be in when Freeswitch is NOT
running? Should they all clear?

Thanks in advance,
Niall.


--
--
Sremium Ltd.

Reg Number: 451937

Mobile: +353 (0)87 2393174
Web: www.sremium.com

The information transmitted is intended only for the person or entity
to which it is addressed and may contain confidential and/or
privileged material. Statements and opinions expressed in this e-mail
may not represent those of Sremium. Any review, retransmission,
dissemination or other use of, or taking of any action in reliance
upon, this information by persons or entities other than the intended
recipient is prohibited. If you received this in error, please contact
the sender immediately and delete the material from any computer.

_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org

[msc at freeswitch.org]

Pastebin your configs. Also, are you using libpri?

-MC

Sent from my iPhone

On Jul 30, 2009, at 7:26 AM, Niall Crosby <niall.crosby@gmail.com>
wrote:

[niall.crosby at gmail.com]

Not libpri (hadn't heard of this), am using Openzap.

Sangoma support got back and say that the alarms should be cleared
even when Freeswitch is not running (which is not the case for me) so
looks like it's nothing to do with Freeswitch.

Also Sangoma pointed out to me that my Rx Level is < -44db which I'm
told is far to low. So think it best not to take time on the
Freeswitch list until I get my hardware sorted out.

Thanks,
Niall.

2009/7/30 Michael S Collins <msc@freeswitch.org>:

[Prometheus001 at gmx.net]

Firstly I would try get get rid of the sangoma errors. There are 2 errors:

Short Circuit: ON
Loss of Signal: ON

So either the card is not configured correctly or there is a cabling
problem. What is your wanpipe1.conf?

Second, if euro doesn't work, try Q931.
I had success with that some time ago.

Best regards
Peter

Niall Crosby schrieb:

[niall.crosby at gmail.com]

Thanks for help.

Got my alarms sorted - telco had problem there.

As for my Freeswitch problem, chaning to Q931 clears the error message.

I was asked by telco to specifically use telco, will using Q931 cause
any issues for me?

Thanks again,
Niall.

2009/7/31 Peter P GMX <Prometheus001@gmx.net>:

[Prometheus001 at gmx.net]

[niall.crosby at gmail.com]

Sorry, my mistake.

I was asked by telco to specifically use Euro dialect, will using Q931
cause any issues?

tnks

2009/7/31 Peter P GMX <Prometheus001@gmx.net>:

[anthony.minessale at g...]

euro and q931 are the same thing on most devices.
Europe uses pure q931 where most other places use "enhanced" versions of it.



On Fri, Jul 31, 2009 at 9:45 AM, Niall Crosby <niall.crosby@gmail.com (niall.crosby@gmail.com)> wrote:

[Prometheus001 at gmx.net]

Q.931 and Q.921 are protocols for Euro ISDN. So this is the right protocol.
See here: http://www.voip-info.org/wiki/view/EuroISDN

Best regards Peter

Niall Crosby schrieb: