VoIP Mailing List Archives

[MPeace at edcogroupinc...]

I just installed FS on a fresh Centos 5.3 install, everything went perfect. I loaded x0lite up on a couple of hosts and they registered and worked fine. Then I moved the Centos server to a new subnet on out network that we have tons of boxes on and have all the routes already configured on and now the Sip phones will no longer register. No other changes have been made on the FreeSwitch server other than changing the IP. BTW I can ping to and from the FS server and the hosts and the firewall is off on the FS server and the hosts.

I plugged a laptop with X-lite into a switch on the same network so the packets don’t even need to route and it still won’t register!

BTW I also downloaded 3CX VoIP phone and it behaves the same way.

Any ideas?

TIA


EDCO Group, Inc.
Phone: (800) 999-3456
Fax: (800) 999-3551
Web: http://www.edcogroupinc.com/

Confidentiality Notice: The information contained in this e-mail message (including any attachments) may contain confidential and privileged information, and is for the sole use of the intended recipient(s). If you are not the intended recipient, any unauthorized review, use, or disclosure or distribution is strictly prohibited. If you have received this message in error, please notify the sender by replying to this e-mail message or by telephone at (800) 999-3456 and permanently destroy all copies of the original message (including any attachments), along with any reply, and delete them from your system.

[brian at freeswitch.org]

Did you happen to hard code an IP in your vars.xml?

/b

On Aug 24, 2009, at 3:42 PM, Mike Peace wrote:

[MPeace at edcogroupinc...]

I haven’t changed any of the conf files.

Mike Peace
Network Analyst
EDCO, The Document People
Direct 417-447-3367


From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Brian West
Sent: Monday, August 24, 2009 3:46 PM
To: freeswitch-users@lists.freeswitch.org
Subject: Re: [Freeswitch-users] Moved Freeswitch to new subnet.



Did you happen to hard code an IP in your vars.xml?


/b


On Aug 24, 2009, at 3:42 PM, Mike Peace wrote:






I just installed FS on a fresh Centos 5.3 install, everything went perfect. I loaded x0lite up on a couple of hosts and they registered and worked fine. Then I moved the Centos server to a new subnet on out network that we have tons of boxes on and have all the routes already configured on and now the Sip phones will no longer register. No other changes have been made on the FreeSwitch server other than changing the IP. BTW I can ping to and from the FS server and the hosts and the firewall is off on the FS server and the hosts.



I plugged a laptop with X-lite into a switch on the same network so the packets don’t even need to route and it still won’t register!



BTW I also downloaded 3CX VoIP phone and it behaves the same way.



Any ideas?



TIA








EDCO Group, Inc.
Phone: (800) 999-3456
Fax: (800) 999-3551
Web: http://www.edcogroupinc.com/

Confidentiality Notice: The information contained in this e-mail message (including any attachments) may contain confidential and privileged information, and is for the sole use of the intended recipient(s). If you are not the intended recipient, any unauthorized review, use, or disclosure or distribution is strictly prohibited. If you have received this message in error, please notify the sender by replying to this e-mail message or by telephone at (800) 999-3456 and permanently destroy all copies of the original message (including any attachments), along with any reply, and delete them from your system.

[msc at freeswitch.org]

On Mon, Aug 24, 2009 at 2:01 PM, Mike Peace <MPeace@edcogroupinc.com (MPeace@edcogroupinc.com)> wrote:

[MPeace at edcogroupinc...]

“Registration error: 408-Request Timeout”

Mike Peace
Network Analyst
EDCO, The Document People
Direct 417-447-3367

From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Michael Collins
Sent: Monday, August 24, 2009 4:18 PM
To: freeswitch-users@lists.freeswitch.org
Subject: Re: [Freeswitch-users] Moved Freeswitch to new subnet.



On Mon, Aug 24, 2009 at 2:01 PM, Mike Peace <MPeace@edcogroupinc.com (MPeace@edcogroupinc.com)> wrote:
I haven’t changed any of the conf files.




What happens when you try to register? Do you get 480? (timeout) Or something else?
-MC


EDCO Group, Inc.
Phone: (800) 999-3456
Fax: (800) 999-3551
Web: http://www.edcogroupinc.com/

Confidentiality Notice: The information contained in this e-mail message (including any attachments) may contain confidential and privileged information, and is for the sole use of the intended recipient(s). If you are not the intended recipient, any unauthorized review, use, or disclosure or distribution is strictly prohibited. If you have received this message in error, please notify the sender by replying to this e-mail message or by telephone at (800) 999-3456 and permanently destroy all copies of the original message (including any attachments), along with any reply, and delete them from your system.

[msc at freeswitch.org]

On Mon, Aug 24, 2009 at 2:26 PM, Mike Peace <MPeace@edcogroupinc.com (MPeace@edcogroupinc.com)> wrote:

[MPeace at edcogroupinc...]

It does the same thing, does anything get set during the install that would remember or cache the old network settings? I can access anything from the FS server on any of several networks and vice-versa but the SIP will not register, again no firewalls are upon any of the test hosts.
Doesn’t make sense to me.

Mike Peace
Network Analyst
EDCO, The Document People
Direct 417-447-3367

From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Michael Collins
Sent: Monday, August 24, 2009 4:34 PM
To: freeswitch-users@lists.freeswitch.org
Subject: Re: [Freeswitch-users] Moved Freeswitch to new subnet.



On Mon, Aug 24, 2009 at 2:26 PM, Mike Peace <MPeace@edcogroupinc.com (MPeace@edcogroupinc.com)> wrote:
“Registration error: 408-Request Timeout”


Sorry for the the typo - 408 = timeout. (480 = temp unavail)

Try stopping iptables in Linux and try again. Sounds like something is interfering with your packets getting from here to there...
Try:

/etc/init.d/iptables stop

And then see if your packets can move again.

-MC

[msc at freeswitch.org]

On Mon, Aug 24, 2009 at 2:49 PM, Mike Peace <MPeace@edcogroupinc.com (MPeace@edcogroupinc.com)> wrote:

[MPeace at edcogroupinc...]

I fired up Wireshark on each side and I can see the SIP register request coming from the laptop, the Freeswitch server replies with a Destination Unreachable (Port unreachable) message.

I rebooted the Server and now I get a “Registration error; 405 Method not allowed” on the softphone and the Wiresharp capture shows: “Status 405 Method Not Allowerd (0 bindings).

It does this even after I stop and restart the Freeswitch service.

Shouldn’t all the ports be open if the firewall and SELunix are disabled?

Mike Peace
Network Analyst
EDCO, The Document People
Direct 417-447-3367

From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Michael Collins
Sent: Monday, August 24, 2009 5:32 PM
To: freeswitch-users@lists.freeswitch.org
Subject: Re: [Freeswitch-users] Moved Freeswitch to new subnet.



On Mon, Aug 24, 2009 at 2:49 PM, Mike Peace <MPeace@edcogroupinc.com (MPeace@edcogroupinc.com)> wrote:
It does the same thing, does anything get set during the install that would remember or cache the old network settings? I can access anything from the FS server on any of several networks and vice-versa but the SIP will not register, again no firewalls are upon any of the test hosts.
Doesn’t make sense to me.




Time to bust out tcpdump and/or wireshark to make 100% certain you know what's happening with all those SIP packets.

[msc at freeswitch.org]

On Tue, Aug 25, 2009 at 7:20 AM, Mike Peace <MPeace@edcogroupinc.com (MPeace@edcogroupinc.com)> wrote:

[MPeace at edcogroupinc...]

I get a bash: sofia: command not found. Is there something I need to add to my config to use these commands?

From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Michael Collins
Sent: Tuesday, August 25, 2009 10:55 AM
To: freeswitch-users@lists.freeswitch.org
Subject: Re: [Freeswitch-users] Moved Freeswitch to new subnet.



On Tue, Aug 25, 2009 at 7:20 AM, Mike Peace <MPeace@edcogroupinc.com (MPeace@edcogroupinc.com)> wrote:
I fired up Wireshark on each side and I can see the SIP register request coming from the laptop, the Freeswitch server replies with a Destination Unreachable (Port unreachable) message.

I rebooted the Server and now I get a “Registration error; 405 Method not allowed” on the softphone and the Wiresharp capture shows: “Status 405 Method Not Allowerd (0 bindings).



Hmm... can you fire up FS and then do "sofia status" and tell us if the internal profile looks okay? Also, do "sofia status profile internal" and capture the output. Something fishy is going on...
-MC

[mike at jerris.com]

if you want to run that at your prompt instead of at the fs_cli you can do this:

function sofia() { fs_cli -x "$(echo "sofia $@")"; }


(thanks ray for the bash foo)


Mike

On Aug 25, 2009, at 1:04 PM, Mike Peace wrote:

[msc at freeswitch.org]

On Tue, Aug 25, 2009 at 10:04 AM, Mike Peace <MPeace@edcogroupinc.com (MPeace@edcogroupinc.com)> wrote:

[MPeace at edcogroupinc...]

Ok, figured out from your post to load the FS-CLI in order to run the Sophia status Michael mentioned.

Now I get: [ERROR] libs/esl/fs_cli.c.639 main() Error Connecting [Socket Connection Error] when running ./fs_cli from a terminal window in /usr/local/freeswitch/bin where fs_cli is located.

Mike
From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Michael Jerris
Sent: Tuesday, August 25, 2009 12:39 PM
To: freeswitch-users@lists.freeswitch.org
Subject: Re: [Freeswitch-users] Moved Freeswitch to new subnet.



if you want to run that at your prompt instead of at the fs_cli you can do this:


function sofia() { fs_cli -x "$(echo "sofia $@")"; }



(thanks ray for the bash foo)



Mike


On Aug 25, 2009, at 1:04 PM, Mike Peace wrote:




I get a bash: sofia: command not found. Is there something I need to add to my config to use these commands?



From: freeswitch-users-bounces@lists.freeswitch.org (freeswitch-users-bounces@lists.freeswitch.org) [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Michael Collins
Sent: Tuesday, August 25, 2009 10:55 AM
To: freeswitch-users@lists.freeswitch.org (freeswitch-users@lists.freeswitch.org)
Subject: Re: [Freeswitch-users] Moved Freeswitch to new subnet.




Hmm... can you fire up FS and then do "sofia status" and tell us if the internal profile looks okay? Also, do "sofia status profile internal" and capture the output. Something fishy is going on...
-MC

[mrene_lists at avgs.ca]

It means freeswitch is not running. You need to start it with /usr/local/freeswitch/bin/freeswitch -nc

@MikeJ: Nice bash scripting

Mathieu Rene
Avant-Garde Solutions Inc
Office: + 1 (514) 664-1044 x100
Cell: +1 (514) 664-1044 x200
mrene@avgs.ca (mrene@avgs.ca)








On 25-Aug-09, at 1:53 PM, Mike Peace wrote: