VoIP Mailing List Archives

[techyjt at bellsouth.net]

Hello group,


I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error:


Loading DAHDI hardware modules:
wctdm24xxp: done
Running dahdi_cfg: done.
Missing '/sys/bus/astribanks/drivers/xppdrv/sync'


I found some steps at https://issues.asterisk.org/jira/browse/DAHLIN-325?page=com.atlassian.jira.plugin.system.issuetabpanels:all-tabpanel


Here is the output of the commands listed there:
$ sudo lspci -d d161:* -v
04:01.0 Ethernet controller: Digium, Inc. Wildcard TDM800P 8-port analog card (rev 11)
Subsystem: Digium, Inc. Wildcard TDM800P 8-port analog card
Flags: bus master, medium devsel, latency 32, IRQ 16
I/O ports at d000 [size=256]
Memory at f7c20000 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at f7c00000 [disabled] [size=128K]
Capabilities: [c0] Power Management version 2
Kernel driver in use: wctdm24xxp
Kernel modules: wctdm24xxp


$ sudo dahdi_scan
[1]
active=yes
alarms=OK
description=Wildcard TDM800P
name=WCTDM/0
manufacturer=Digium
devicetype=Wildcard TDM800P
location=PCI Bus 04 Slot 02
basechan=1
totchans=8
irq=0
type=analog
port=1,FXO
port=2,FXO
port=3,FXO
port=4,FXO
port=5,FXS
port=6,FXS
port=7,FXS
port=8,FXS


$ sudo dahdi_cfg -vvvvvvv
DAHDI Tools Version - 2.7.0.1


DAHDI Version: 2.8.0-rc2
Echo Canceller(s): MG2
Configuration
======================




Channel map:


Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 04)
Channel 05: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 05)
Channel 06: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 06)
Channel 07: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 07)
Channel 08: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 0


8 channels to configure.


Setting echocan for channel 1 to mg2
Setting echocan for channel 2 to mg2
Setting echocan for channel 3 to mg2
Setting echocan for channel 4 to mg2
Setting echocan for channel 5 to mg2
Setting echocan for channel 6 to mg2
Setting echocan for channel 7 to mg2

Setting echocan for channel 8 to mg2


I have ran the command dahdi_genconf system and dahdi_genconf system modules trying to reload dahdi each time.


Here is the output of my /etc/dahdi/system.conf file:
# Autogenerated by /usr/sbin/dahdi_genconf on Sat Nov 23 14:42:33 2013
# If you edit this file and execute /usr/sbin/dahdi_genconf again,
# your manual changes will be LOST.
# Dahdi Configuration File
#
# This file is parsed by the Dahdi Configurator, dahdi_cfg
#
# Span 1: WCTDM/0 "Wildcard TDM800P" (MASTER)
fxsks=1
echocanceller=mg2,1
fxsks=2
echocanceller=mg2,2
fxsks=3
echocanceller=mg2,3
fxsks=4
echocanceller=mg2,4
fxoks=5
echocanceller=mg2,5
fxoks=6
echocanceller=mg2,6
fxoks=7
echocanceller=mg2,7
fxoks=8
echocanceller=mg2,8


# Global data


loadzone = us

defaultzone = us


What any ideas?


Thanks.

[sruffell at digium.com]

On Sat, Nov 23, 2013 at 11:47:49AM -0800, Joseph Towery wrote: