VoIP Mailing List Archives

[matthew.lockwood at gm...]

Hi,

I've just managed to get FreeSWITCH installed. I'm using the default config files which works fine with X-Lite. The problem is, I can't use any other softphone other than X-Lite. i've tried YakaPhone, Zoiper, Adore Softphone, QuteCom, and Linphone. I'd normally not say this is a problem, but X-Lite is having issues with my Netgear router (it causes it to continually restart ... there are other posts about this elsewhere and the solutions aren't working.)

The only other relevant thing I can think of to add to this topic is that X-Lite, on its first registration always gives me a timeout error, and then successfully registers. After a few minutes, the router reboots.

Matt


PS. I apologize if this posts twice - I seemed to have an issue with my mail client and I don't think it sent the first time.

[matthew.lockwood at gm...]

Hi,

I've just managed to get FreeSWITCH installed. I'm using the default config files which works fine with X-Lite. The problem is, I can't use any other softphone other than X-Lite. i've tried YakaPhone, Zoiper, Adore Softphone, QuteCom, and Linphone. I'd normally not say this is a problem, but X-Lite is having issues with my Netgear router (it causes it to continually restart ... there are other posts about this elsewhere and the solutions aren't working.)

The only other relevant thing I can think of to add to this topic is that X-Lite, on its first registration always gives me a timeout error, and then successfully registers. After a few minutes, the router reboots.

Matt

[brian at freeswitch.org]

I'm going to have to guess that you're doing this all on the same machine?

/b

On Jun 3, 2009, at 8:20 AM, Matthew Lockwood wrote:

[matthew.lockwood at gm...]

No, FS is installed on a VPS. I'm just connecting through my cable connection.

M

On Wed, Jun 3, 2009 at 8:18 AM, Brian West <brian@freeswitch.org (brian@freeswitch.org)> wrote:

[intralanman at freeswi...]

Matthew Lockwood wrote:

[brian at freeswitch.org]

I'm guessing NAT problem, Not sure those other phones do STUN and traverse nat properly.

/b

On Jun 3, 2009, at 10:34 AM, Matthew Lockwood wrote:

[matthew.lockwood at gm...]

SPI disabled. There's no obvious option to disable SIP ALG, but NAT filtering was changed from secure to open. Problem still persists.

On Wed, Jun 3, 2009 at 8:36 AM, Raymond Chandler <intralanman@freeswitch.org (intralanman@freeswitch.org)> wrote:

[asannucci at gmail.com]

Have you open the necesary ports in the VPS firewall? Regards

[brian at freeswitch.org]

Thats not the problem..

Phone registers to freeswitch has 192.168.0.100 in the sip packet... FS sends a challenge back to 192.168.0.100 which obviously will FAIL cuz that network isn't anywhere near the VPS box...




Go to the FreeSWITCH box and type "sofia profile internal siptrace on" and I'll suspect you see this exact behavior.


/b





On Jun 3, 2009, at 10:42 AM, Matthew Lockwood wrote:

[matthew.lockwood at gm...]

When I type that verbatim, I get the following error:

-ERR Unknown command!

M

On Wed, Jun 3, 2009 at 8:47 AM, Brian West <brian@freeswitch.org (brian@freeswitch.org)> wrote:

[brian at freeswitch.org]

Update to SVN trunk.

/b

On Jun 3, 2009, at 12:00 PM, Matthew Lockwood wrote:

[matthew.lockwood at gm...]

Is that stable enough to use in production?



On Wed, Jun 3, 2009 at 10:04 AM, Brian West <brian@freeswitch.org (brian@freeswitch.org)> wrote:

[intralanman at freeswi...]

Matthew Lockwood wrote:

[brian at freeswitch.org]

It usually is... if you pop on IRC people can tell you one way or another. Issues never hang around for very long!

/b

On Jun 3, 2009, at 12:16 PM, Raymond Chandler wrote:

[matthew.lockwood at gm...]

It's installing now. I'll get back with the results shortly.

On Wed, Jun 3, 2009 at 10:34 AM, Brian West <brian@freeswitch.org (brian@freeswitch.org)> wrote: