VoIP Mailing List Archives
Mailing list archives for the VoIP community |
|
| View previous topic :: View next topic |
| Author |
Message |
gopalakrishnan.an at g...
Guest
|
 Posted: Fri Feb 12, 2016 11:02 am Post subject: [asterisk-users] NAT on IPsec Tunnel |
 |
|
Now incoming works fine, this is because of my SonicWALL firmware issue, tried with different SonicWALL inbound works.
But for outbound am getting 408 request time out error in the NAT on VPN tunnel.
On Fri, Feb 12, 2016 at 3:50 AM Gopalakrishnan N <gopalakrishnan.an@gmail.com (gopalakrishnan.an@gmail.com)> wrote:
| Quote: | Hi all,
Am using Asterisk 11.2.1. And for site testing, Verizon is doing Interop testing with site to site IPsec tunnel and with public IP over the tunnel.
Problem is when I do an inbound call, only a IVR message plays, whereas am not able to transfer a call to extension, or dtmf not even works and even outbound getting 408 request timeout.
By all means I have configured externaddr and localnet in my sip.conf.
Verizon says still the contact information shows my private IP, even though I configured externaddr.
When I route the incoming call directly to an hardphone extension, am not able to answer the call in the hardphone, the ring LED keeps in blinking even though i pickup the receiver, which is strange i haven;t seen.
Can someone had any of this issue or throwing out any information would help me.
Attached PCAP File:
InboundCall_Direct_Extension - not able to answer in the hardphone
InboundCall_DTMF - Inbound call plays a message and wait for DTMF, where its not recognized
Tks.
|
|
|
| Back to top |
|
 |
gopalakrishnan.an at g...
Guest
|
| Posted: Wed Feb 17, 2016 12:01 am Post subject: [asterisk-users] NAT on IPsec Tunnel |
|
|
Finally got it worked, the issue was E164 callerid format, where i set it up, after removing the E164 format its was thru.
Regards
On Fri, Feb 12, 2016 at 9:31 PM Gopalakrishnan N <gopalakrishnan.an@gmail.com (gopalakrishnan.an@gmail.com)> wrote:
| Quote: | Now incoming works fine, this is because of my SonicWALL firmware issue, tried with different SonicWALL inbound works.
But for outbound am getting 408 request time out error in the NAT on VPN tunnel.
On Fri, Feb 12, 2016 at 3:50 AM Gopalakrishnan N <gopalakrishnan.an@gmail.com (gopalakrishnan.an@gmail.com)> wrote:
| Quote: | Hi all,
Am using Asterisk 11.2.1. And for site testing, Verizon is doing Interop testing with site to site IPsec tunnel and with public IP over the tunnel.
Problem is when I do an inbound call, only a IVR message plays, whereas am not able to transfer a call to extension, or dtmf not even works and even outbound getting 408 request timeout.
By all means I have configured externaddr and localnet in my sip.conf.
Verizon says still the contact information shows my private IP, even though I configured externaddr.
When I route the incoming call directly to an hardphone extension, am not able to answer the call in the hardphone, the ring LED keeps in blinking even though i pickup the receiver, which is strange i haven;t seen.
Can someone had any of this issue or throwing out any information would help me.
Attached PCAP File:
InboundCall_Direct_Extension - not able to answer in the hardphone
InboundCall_DTMF - Inbound call plays a message and wait for DTMF, where its not recognized
Tks.
|
|
|
|
| Back to top |
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Search
