VoIP Mailing List Archives
Mailing list archives for the VoIP community |
|
| View previous topic :: View next topic |
| Author |
Message |
gandresin at gmail.com
Guest
|
 Posted: Tue Mar 04, 2008 2:04 pm Post subject: [asterisk-users] Problems configuring Astribank |
 |
|
Hi, all
My Asterisk uses a Digium TE120Pand I would like to add an Astribank
zaptel_hardware sees is, but I cannot get it working
pbx:~# zaptel_hardware
Argument "IRQ" isn't numeric in numeric comparison (<=>) at
/usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114.
usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware
pci:0000:04:00.0 wcte12xp+ d161:0120 Wildcard TE12xP
In the Astribank line (module part) there is a "-" sign after the
module name (while the TE120P has a "+" sign).
Does that mean anything?
genzaptelcong doesn't generate any config for the Astribank.
Can anyone send a copy of their working Astribank settings?
I am concerned about the span used by the Astribank. I just cannot
find anything that gives me a clue...
Thanks in advance.
Regards,
--
Andres Jimenez
GPG : http://www.andresin.com/gpg/gandresin at gmail.com.asc |
|
| Back to top |
|
 |
gandresin at gmail.com
Guest
|
| Posted: Tue Mar 04, 2008 2:44 pm Post subject: [asterisk-users] Problems configuring Astribank |
|
|
I just upgraded zaptel to 1.4.9.2 (and rebuild everything, of course)
but no improvements.
zaptel_hardware's output is the same and genzaptelconf
I forgot to mention that zapconf fails too...
pbx:~# zapconf
Argument "IRQ" isn't numeric in numeric comparison (<=>) at
/usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114.
Failed probing type for channel IRQ at /usr/sbin/zapconf line 230.
Cheers,
Andres
On Tue, Mar 4, 2008 at 7:04 PM, Andres Jimenez <gandresin at gmail.com> wrote:
| Quote: | Hi, all
My Asterisk uses a Digium TE120Pand I would like to add an Astribank
zaptel_hardware sees is, but I cannot get it working
pbx:~# zaptel_hardware
Argument "IRQ" isn't numeric in numeric comparison (<=>) at
/usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114.
usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware
pci:0000:04:00.0 wcte12xp+ d161:0120 Wildcard TE12xP
In the Astribank line (module part) there is a "-" sign after the
module name (while the TE120P has a "+" sign).
Does that mean anything?
genzaptelcong doesn't generate any config for the Astribank.
Can anyone send a copy of their working Astribank settings?
I am concerned about the span used by the Astribank. I just cannot
find anything that gives me a clue...
Thanks in advance.
Regards,
--
Andres Jimenez
GPG : http://www.andresin.com/gpg/gandresin at gmail.com.asc
|
--
Andres Jimenez
GPG : http://www.andresin.com/gpg/gandresin at gmail.com.asc |
|
| Back to top |
|
|
tzafrir.cohen at xorco...
Guest
|
| Posted: Tue Mar 04, 2008 3:46 pm Post subject: [asterisk-users] Problems configuring Astribank |
|
|
On Tue, Mar 04, 2008 at 07:04:15PM +0000, Andres Jimenez wrote:
| Quote: | Hi, all
My Asterisk uses a Digium TE120Pand I would like to add an Astribank
zaptel_hardware sees is, but I cannot get it working
|
What version of Zaptel is this?
| Quote: | pbx:~# zaptel_hardware
Argument "IRQ" isn't numeric in numeric comparison (<=>) at
/usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114.
|
A known issue. Should be fixed on next version. This should also cause
some problems to zapconf. Until then, use genzaptelconf.
| Quote: | usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware
|
http://zaptel.tzafrir.org.il/README.Astribank.html#_troubleshhoting
"If lsusb shows the Product ID as 11x1 - only the USB firmware is loaded
and not the FPGA firmware is loaded. If this is still the case after a
while - either the firmware loading has failed or you don't have
fpga_load. Make sure you have libusb-dev(el) installed when building
Zaptel."
Do you have fpga_load built? If not: maybe libusv-dev[el] was not installed
when you configured Zaptel? If this is zaptel 1.2: you need to
explicitly run 'make -C xpp/utils install'
(that file is an HTML-zed version of the file README.Astribank from
latest SVN version of Zaptel)
| Quote: | pci:0000:04:00.0 wcte12xp+ d161:0120 Wildcard TE12xP
In the Astribank line (module part) there is a "-" sign after the
module name (while the TE120P has a "+" sign).
Does that mean anything?
|
Quoting the man page of zaptel_hardware:
The second field shows which driver should handle the device. a "-"
sign marks that the device is not yet handled by this driver. A "+"
sign means that the device is handled by the driver.
| Quote: |
genzaptelcong doesn't generate any config for the Astribank.
|
Right. The firmware wasn't even loaded. When it will be, genzaptelconf
and co. will do their job.
| Quote: |
Can anyone send a copy of their working Astribank settings?
|
http://zaptel.tzafrir.org.il/README.Astribank.html#_sample_configurations
But then again, it will not really be necessary.
--
Tzafrir Cohen
icq#16849755 jabber:tzafrir.cohen at xorcom.com
+972-50-7952406 mailto:tzafrir.cohen at xorcom.com
http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir |
|
| Back to top |
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Search
