VoIP Mailing List Archives

[jeff at jeff.net]

Hello,

I am having odd issues with a new PRI based installation. Outbound
calls work for all numbers except those that terminate at Sprint! The
telco is new to PRI (this is in the Caribbean) and say that Sprint is
rejecting the calls, and asked for our PRI settings so they can work
with their switch manufacturer. We are using the bare minimum default
settings, but I can imagine that a whole ton of configurable settings
exist that I have never played with.

Is there a way to dump all of the configurable settings for a PRI? The
card is a Digium TE122.

Thanks,

j

--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users

[EWieling at nyigc.com]

I doubt PBX settings (other than CallerID) would break calling to only one specific carrier.

Have you tried pri show span X?

From one of our boxes:

pbx*CLI> pri show span 1
Primary D-channel: 24
Status: Up, Active
Switchtype: National ISDN
Type: CPE
Remote type: Unknown node type
Overlap Dial: 0
Logical Channel Mapping: 0
Timer and counter settings:
N200: 3
N202: 3
K: 7
T200: 1000
T201: 1000
T202: 10000
T203: 10000
T303: 4000
T305: 30000
T308: 4000
T309: 6000
T312: 6000
T313: 4000
T316: -1
N316: 2
T-HOLD: 4000
T-RETRIEVE: 4000
T-RESPONSE: 4000
Q931 RX: 6350
Q931 TX: 5828
Q921 RX: 42786
Q921 TX: 42716
Q921 Outstanding: 0 (TEI=0)
Total active-calls:2 global:1
CC records:
Overlap Recv: No

-----Original Message-----
From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Jeff LaCoursiere
Sent: Tuesday, August 19, 2014 5:00 PM
To: asterisk-users@lists.digium.com >> Asterisk Users Mailing List - Non-Commercial Discussion
Subject: [asterisk-users] Way to dump PRI settings?

Hello,

I am having odd issues with a new PRI based installation. Outbound
calls work for all numbers except those that terminate at Sprint! The
telco is new to PRI (this is in the Caribbean) and say that Sprint is
rejecting the calls, and asked for our PRI settings so they can work
with their switch manufacturer. We are using the bare minimum default
settings, but I can imagine that a whole ton of configurable settings
exist that I have never played with.

Is there a way to dump all of the configurable settings for a PRI? The
card is a Digium TE122.

Thanks,

j

--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users

--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
New to Asterisk? Join us for a live introductory webinar every Thurs:
http://www.asterisk.org/hello

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users

[jeff at jeff.net]

Perfect! Exactly what I was looking for.

Cheers,

j

On 08/19/2014 12:23 PM, Eric Wieling wrote: